How to reproof your waterproof gear.

Gareth    Clothing, General Outdoor     nikwax, reproofing, tech wash, TX direct, waterproof

Having a coat that’s lost it’s breathability and soaks up rain makes for a seriously uncomfortable day out. After our guide to washing down products, we’ve had a fair few requests from folks whose waterproofs have started to be, well, slightly less than waterproof! All jackets slowly lose their ability to repel water, to have rain bead or “rest” on the outside and that’s without even taking in to account your gear getting dirty. So if have been wondering just how to get that new jacket performance back, we’ve put together this guide on how to get your togs repelling water, and breathing easy again.

There are two things you can do to get your jacket working as good as new. First up Washing. You need to wash your jacket first to ensure it is clean, and in case it’s necessary make sure any reproofing can go on easily. In many cases simply washing your jacket will have it back performing near it’s best. It isn’t just a case of washing in normal detergent though as that will make things worse for technical outdoor gear. You need a specialist wash that will get rid of any residues that block breathability and attract water to make your gear “wet out”. There are a few products that will do this, but we really like Nikwax Tech wash for the washing bit. Not only does the hippy in me like it (it’s water based and environmentally friendly man) but it won’t damage the water repellent treatments on the outside of your jacket, nor any waterproof membrane either. To get the best results we reckon our foolproof instructions below will have you covered;

1. Clean your detergent dispenser. Sooper dooper important this bit, if there is any gunk left from your day to day washing, it’ll clog the pores of your gear, stop it breathing as well as stopping any reproofer from going on effectively afterwards.
2. Run your washing machine on it’s hottest wash with nothing in it. This is doing exactly the same thing as cleaning your dispenser by getting rid of the gunk inside. If you have a really grotty machine you might want to do it twice As a side note, our resident Dorset washing repair man Laurie reckons you should do this once in a while anyway to stop stuff building up that can damage your washing machine.
3. Get your gear ready. Loosen all draw cords and close all zips and Velcro so the jacket doesn’t catch. If there are any really filthy bits, rub a bit of neat Tech wash directly on to the affected area(s).
4. Wash a maximum of two items. Simples really, ensures that your stuff gets properly clean.
5. Follow your clothes care instructions.  Most washes should be on a delicate/synthetic wash with a slow spin to stop abrasion of your gear, follow the instruction label on your gear first and foremost.
6. Allow to dry naturally. This is really important if you are using a spray on reproofer later.

Assuming you have followed the instructions above for washing your gear, you won’t need to clean out your washing machine again so it’s just the following;

1. Maximum of two items. Same as above
2. Follow your clothes care instructions. Delicate or synthetic wash on a slow spin thanks people.
3. Warm dry your coat. This last bit isn’t critical but we find that heat ensures that repellency treatments lasts longer. Our order of preference for most effectiveness is tumble dry on a low setting if your garment allows it, shoving it on a hot radiator, popping in an airing cupboard, putting it out to dry in the hot sunshine, or (and be very careful here…) Ironing it on a very low setting.

Going Lighter – Can you make a vest out of a sleeping bag?

Gareth    camping, Clothing     antoine sachs, comforter, down comforter, lightweight, lightweight gear, yeti

We’re pretty chuffed to have worked with some fairly interesting bloggers in our outdoor testing crew, but one of the most exciting for us has been Antoine Sachs, a french outdoors nut who blogs over at Chronique sans Carbones. When he dropped us a line to say that he was going to start making his own gear we were pretty made up, and we asked him to send us his first creation. 7 months later a rather interesting package turned up on our doorstep.

He’s called it his down comforter, and it can either be used as a quilt, as a wrap around insulation vest/piece that will fit underneath an outer shell, as an under hammock insulation piece, or as a seriously warm blanket inside the house when watching Eastenders (Antoine made us put that bit it in!). We’re pretty bowled over by the weight coming in at just 550g. Here’s some more photos of it lying nonchalantly on our conference room table.

One of the issues with sleeping bags for those looking to reduce the weight of their pack is the dead weight of insulation underneath the sleeping bag that you lie on. As it’s compressed, it offers no warmth at all. The comforter gets rid of this wasted insulation by acting as a quilt with ties to fasten either under your body or under your mattress so that just your top half is insulated. It then has drawcords at the at the top and bottom with your sleeping mattress underneath insulating you from the ground.

You can also with a little fiddling use it as an insulated vest, wrapping it around your head and Torso. We’ve yet to perfect the knack but we’ll hopefully have an online Skype demo from Antoine soon. If that works well it would mean the weight savings from having a sleeping bag and jacket combined would be substantial.

The one we have been sent is a size medium with 350g of 860 European Fill down on the inside. The quality of the piece is immediately apparent, it lofted faster than a speeding bullet. He’s currently using Yeti to manufacture it, but this could change. We’ve stocked Yeti in the past and know that their stuff is on a par with Western Mountaineering as a comparison.

Antoine reckons it will work down to -10 as an insulation piece under a hard shell or external jacket. Your jacket would need to be a little baggier than normal for the comforter to loft and work properly. As a sleeping system he thinks it’s more suitable down to 0c, possibly -5c if you use a close bivvy bag to help trap air more effectively.

We had a chance to test it this weekend, and based on our feedback and others, Antoine is looking to make some adjustments to the connectors. In the meantime the question we want to ask you is, if we stocked something like this, would you be interested in it? What would you expect to pay for the comforter?

What’s the best Insulation for cold weather?

Gareth    Clothing, General Outdoor     down, fleece, insulation, synthetic insulation

Sadly there is no “wonder insulation” that’s going to keep you warm, be breathable, pack down small, deal with snow & rain, save you from an avalanche and make you a cup of tea in the morning. We think it’s a horses for courses approach for your insulating layers, get the right thing for the right situation. So without further ado, let’s take a look at the three main types you can choose.

DOWN: Natures warmth, the fluffy stuff underneath a birds feathers.

SYNTHETIC: Synthetic fibres woven together to trap air and keep you toasty.

FLEECE: Another synthetic option that’s a fabric in it’s own right (rather than fibres that you put in to a jacket)

Now we’ve sorted out what we’re going to take a look at, let’s dive in and take a quick look at the good and the bad of our contestants.

Down Jackets & Vests

GOOD STUFF: The highest Warmth to Weight ratio of all the options here, goose down is fabulous stuff for trapping air and keeping you warm. It feels seriously sexy to wear, is incredibly lightweight, and packs down smaller than any of the other options here. Great to pull on after a hard day on the mountain, or when wandering out and about.

NOT SO GOOD STUFF: If down gets wet it doesn’t work, so it’s really important to keep it dry at all times. We reckon it works best in cold, snowy climates, or where you bring along a waterproof to stop it getting damp. A little more expensive than some of the other options and maybe too hot if you are doing energetic activities.

STUFF TO LOOK OUT FOR. Without boring you, down is graded according to fill power, e.g how much space a load of down takes up by weight, the range goes from 450 through to 900 odd, the higher the number, the warmer (and lighter) the down.

Synthetic Jackets

GOOD STUFF: Synthetic Insulation is best known with examples such as Primaloft or own brand examples like The North Face’s Heatseeker. Water resistant, it retains a lot of it’s insulating properties even if soaked through, and it’s less expensive than down.

NOT SO GOOD STUFF: It has a greater bulk and weight than down and is less breathable.

STUFF TO LOOK OUT FOR: A favourite with climbers and those who use their insulation out and about. It works best in wet environments, which apparently we get rather a lot of here in the UK!

Fleece Jackets & Vests

GOOD STUFF: Fleece has amazing breathability, and is an awesome choice if you are doing blood pumping activities in the cold. Fleece is water resistant, drys quickly and is great value for money.

NOT SO GOOD STUFF: Fleece is not usually windproof so unless you have some sort of shell layer over the top, the cold wind is going to go whistling through you and take that trapped air and heat away. Relatively heavy and bulky compared to some of the other options.

STUFF TO LOOK OUT FOR: The best known fleece fabric is Polartec, but there are many other own brand examples out there too. Fleece comes in a variety of different flavours e.g. lightweight, midweight & heavyweight.

So there you have our quick guide to insulation. We reckon you need to balance your budget, activity and whether you are wearing it during the day or at journeys end. If you are a backpacker for example, weight is perhaps the most important thing to consider. If you need to get warm at camp at the end of the day, we would suggest grabbing a down vest or jacket. Down is also great if you are just taking the dog out for a quick walk. Climbing and need a belay piece? It has to be Synthetic. Running or walking out in the cold? Grab a fleece to wear underneath your windshirt or waterproof.

What’s your favourite insulation piece when the cold come round?

GoreTex Active Shell – What’s the story?

Gareth    Clothing     active shell, goretex, jackets, waterproof, winter jacket

The 1980′s saw a fabric introduced that revolutionised outdoor clothing – the introduction of Goretex. As the worlds first waterproof yet breathable fabric, it was a sea change in the way that people enjoyed outdoor activities. Before, your choice was simple. Drown in your own sweat, or drown in the rain. I wasn’t the only one who dreaded being made to wear a “Cagoul”, and the feel of wet clammy rubber against my skin. The world outdoors definitely became more of a comfortable place as a result.

One of the first Goretex pieces, the Berghaus Lightning Jacket

So here we are nearly 30 years later, and Gore have come up with the latest version of their technology, called Active Shell. We are going to be getting in several Active shell pieces this winter, and before they come in, we wanted to explain just why we think these new pieces of clothing are so darn cool. Our job is so easy though. We can sum it up thus

1) It’s more breathable than previous versions of Goretex. High aerobic folks such as runners, cyclists, and climbers are going to be big fanboys and girls of this new fabric

2) It’s lighter than any of their other fabrics. It’s ideal for those who want to move fast and light, yet retain decent levels of weather protection.

3) This is just our own opinion having tried on a couple of different jackets, but we think that they are a step up in terms of comfort as well. Less like a crisp bag, they are a bit more flexible and comfortable next to skin. Please note that this is based on the samples we have tried on, so the real deal could be different. Oh apparently the value of your house can go up as well as down.

So how have they done it I hear you ask? Well you will be pleased to know that there was no magician with a rabbit, or a pentagram on the floor. They have managed to make the membrane itself lighter, and by getting the scrim, or backing fabric to integrate straight on to the membrane itself. Both of these manufacturing processes have made the garments lighter, and reduced resistance for water vapour and sweat to get through.

Now we have two of these new jackets coming in for Winter, first up, the Adidas Men’s Terrex Gore-Tex Active Shell Jacket. Adidas are a relative new player in the outdoor market but they have hit the ground running in our humble opinion. We actually got to have a bit of a sneak peak of their gear earlier in the year. The weight is a paltry 370 grammes, we love the laser cut and bonded detailing, and the built in vents. Check out our Video on the whole range here, the new jacket is first up;

Second up is a British classic, it’s Mountain Equipment’s Firefox Jacket. Now the firefox jacket was released a couple of years ago with a unique fit. The fit’s become much more of a standard ME fit, and they have now changed the fabric to Goretex Active Shell as well. The weight is slightly lower than the Adidas coming in at 320 grammes, it features their Mountain Hood adjustment system, and pit zips in case you are on fire.

So more breathable, lighter and more comfortable is the new order of the day with Goretex’s Active Shell. We’re getting them in this September and already the anticipation is building here. If you have any questions at all on the new fabric, or any comments, please post away below.

All new Adidas winter 2011 collection – including Terrex Active Shell

Gareth    Clothing, General Outdoor     active shell, adidas, goretex, primaloft, terrex, winter 2011

We recently had Jon down from Adidas to guide us through the new Autumn Winter collection 2011. We were rather excited to have him down as this will be the first time we will stock both the Adidas clothing range as well as their footwear. You can tell just how excited I was from this video below!

There were quite a few pieces that really stood out, first the Terrex Primaloft Parka.

It looks like a great belay jacket with some about town practicality. I was particularly impressed with the adjustability of the hood. Coming in at roughly 900g it’s a solid piece and is backed up with Climaproof storm, Adidas’ own waterproof breathable fabric.

Next up was the Terrex Hybrid pant. This is a fully featured mountain trouser with a great combo of Gore Windstoppper for most of the trouser, and Climaproof for the high wear areas. You have built in gaiters, and some nice touches with rubberised elastic bands on the inside of the trousers to help grip & keep the trousers up. At £130 this is great value for such a high spec pair of pants.

This was the one that really got my attention. There has been a great deal of noise recently in respect of new technologies when it comes to waterproof, breathable fabrics. Mountain Hardwear have released their Dry-Q for later this year, Polartec have their Neo Shell and Goretex have released Active Shell. All are competing to be the lightest most breathable waterproof fabric out there.

What was immediately different for me was the feel of the Active Shell jacket. I was expecting a light jacket, but the feel was also subtly different to a hard shell being a little more flexible and not quite as noisy when moving. It also felt great next to my skin. Aside from the feel of the fabric, I really liked the permanent built in venting, the helmet compatible hood and the overall weight at just shy of 370g. I am really looking forward to this coming in so will keep you updated as soon as we get to test it in anger on the hill.

We also had a couple of women’s fleeces in some vibrant colours, Lucy tried them on and the cut got the thumbs up.

Finally we had the Terrex Windstopper soft shell jacket, featuring some cavernous pit zips and a great athletic cut, coming in just under 590g in weight. It looks like a good value shell.

All in all a collection that has got us wishing for snow, short days and long nights again – roll on Winter 2011!

Mountain Hardwear – Dry Q first look

Gareth    Clothing     Autumn / Winter 2011, Dry Q, Mountain Hardwear

It’s here. Our first look at the Mountain Hardwear Dri Q product and good god is it a thing of beauty. The images are rather poor having been snapped hurriedly on the old iPhone, but they hopefully give you a flavour of what is to come.

There are three Dry Q products, and then different variants within each of those for soft shell, 2 layer fabrics and 3 layer fabrics. It’s a measure of Mountain Hardwear’s confidence that they are not making any Gore-Tex shell when Dry Q hits the market later this year – a pretty bold move. The one fabric out of the three that is garnering all the attention however is the Dry Q Elite as the competitor to Polartec’s Neo Shell, and Gore-Tex’s active shell. It’s all about the breathability baby when it comes to this fabric. Dry Q’s claim to fame is that it is an air permeable membrane, so it doesn’t just wait for you to get hot and sweaty before it starts to work. It claims to be at least a third more breathable than current fabrics and up to twice as breathable on the 2 – layer version.

We got our hands on the Jovian Jacket, first impressions were good, very light, the fabric feeling like a half way house between a hard shell and soft shell. You had the usual Mountain Hardwear attention to detail, helmet compatible hood with a single pull adjustment system, welded watertight pockets, super long pit zips, some lovely zip pulls they are debating whether to keep or not (please do guys, they are ace) and garages for the zips as well.

Sadly we didn’t get to use it in anger, but as soon as we do, you will be the first to hear about it and let you know how it performs. If it goes on the feel of the fabric though, it’s a big thumbs up from us feeling noticeably lighter and more pliable than existing materials.